Marxmeier Software AG
For troubleshooting purposes, SQL/R provides both client and server side logging.
A client log file may be helpful in situations where either a connection cannot be established or a certain ODBC function call does not behave as expected.
A server log file may be used to analyze any kind of backend problems, for example if a running connection suddenly aborts without obvious reason or a SQL query delivers unexpected results.
Logging is configured by specifying the destination where the log messages are written as well as which functional areas are logged and how detailed the log output should be.
The log destination may be a log file in the file system or a system-defined location such as the syslog on HP-UX and Linux or the Windows event log.
The log flags (log mode) define what will be logged. The functional area is specified with a capital letter A...Z (see below for details). The verbosity, i.e., how much will be logged, is specified with the digits 0...3.
By default, only error messages are logged (verbosity 0).
The asterisk '*' is used to set all functional areas to a specific verbosity. It makes sense first to specify a common verbosity using '*' and then optionally specify which functional areas should be logged differently, as shown in the examples below.
On Windows, a client-side ODBC driver log file is created by editing the LogMode and LogFile parameters in the sqlrodbc.ini file.
To open the sqlrodbc.ini file, use:
The default sqlrodbc.ini file contains commented example settings for LogMode and LogFile. To activate them, the leading ';' semicolon characters must be removed.
With LogMode, the following functional areas may be specified:
For a detailed log except the network transactions, set LogMode = *2N0. For a full log, set LogMode = *3.
LogFile must specify a file in the file system that the invoking process (the ODBC program using the SQL/R ODBC driver) is allowed to write.
For example: LogFile = c:/sqlrodbc.log
On HP-UX and Linux there is no sqlrodbc.ini file. Instead, the SQLR_LOG_FLAGS and SQLR_LOG_FILE environment variables may be set and exported before the invoking process is started.
SQLR_LOG_FLAGS is the equivalent of LogMode and SQLR_LOG_FILE is the equivalent of LogFile.
SQLR_LOG_FLAGS="*2N0" SQLR_LOG_FILE="/tmp/sqlrodbc.log" export SQLR_LOG_FLAGS SQLR_LOG_FILE
Please note: Activating an ODBC driver log file may have significant impact on performance. Therefore it is not recommended to activate an ODBC driver log file for longer than necessary. After having created a log file for troubleshooting, ODBC driver logging should be deactivated.
SQL/R server logging is configured in the odbc.cfg configuration file.
On HP-UX and Linux, this is: /etc/opt/sqlr2/odbc.cfg
On Windows, to open the odbc.cfg file, use:
The original odbc.cfg configuration file contains the commented default settings for the LogFile and LogFlags parameters. To activate them, the leading '#' hash characters must be removed.
The LogFile parameter specifies the log destination. This may either be a file in the file system or set to "syslog" to write any log messages to the HP-UX or Linux syslog or the Windows event log.
With LogFlags, the following functional areas may be specified:
For a full diagnostic log, set LogFlags = *3D2 (The 'D' flag should not be set to 3 because this would generate a lot of messages that are normally not of interest).
To find out details about specific SQL statements, the LogFlags = *1Y2O2 setting is often helpful.
During normal operation, it is recommended to set LogFlags = *1. This will log any connect/disconnect activities. If this is not desired, set LogFlags = *0 during normal operation.
Please note: SQL/R server logging with LogFlags different from *0 or *1 should not be active for longer than necessary to avoid a performance impact on the SQL/R server.
|[ home ]
Please contact email@example.com
if you have any questions
or suggestions regarding this service. © Copyright 1997-2008 Marxmeier Software AG